DRIVELOCK® 50 Bushes

DRIVELOCK® 50 Bushes

735-1
735-2
Machining data
Recommended shaft & hub tolerancesfor full torque transmission are:
< 40mm diameter
Shafts h6 Hub H7
> 40mm diameter
Shafts h8 Hub H8
  • Not self-centering
  • Small radial dimensions
  • Bores 6 to 70mm
  • Bores 25 to 300mm
  • Can be stacked in series (up to 4) to increase torque
Stock no. d (mm) D (mm) L (mm) T F (Nm) P N/mm2 Fa kN
DL50/ 6
6 9 4.5 2.4 0.84 75 3.8
DL50/ 7
7 10 4.5 3 0.86 70 3.9
DL50/ 8
8 11 4.5 4.7 1.17 90 5.3
DL50/ 9
9 12 4.5 7.9 1.76 105 15.6
DL50/ 10
10 13 4.5 9.5 1.91 105 15.6
DL50/ 12
12 15 4.5 11.4 1.91 90 15.6
DL50/ 13
13 16 4.5 13.1 2.02 90 15.6
DL50/ 14
14 18 6.3 22.3 3.18 90 25.4
DL50/ 15
15 19 6.3 24.3 3.24 85 25.4
DL50/ 16
16 20 6.3 27.3 3.42 85 25.4
DL50/ 17
17 21 6.3 29.8 3.51 85 25.4
DL50/ 18
18 22 6.3 32.4 3.61 80 25.4
DL50/ 19
19 24 6.3 49 5.22 110 36
DL50/ 20
20 25 6.3 53 5.33 105 36
DL50/ 22
22 26 6.3 66 6 115 36
DL50/ 24
24 28 6.3 73 6.13 110 36
DL50/ 25
25 30 6.3 72 5.77 95 36
DL50/ 28
28 32 6.3 86 6.33 100 36
DL50/ 30
30 35 6.3 91 6.08 85 36
DL50/ 32
32 36 6.3 131 8.24 115 45
DL50/ 35
35 40 7 171 9.77 110 54
DL50/ 36
36 42 7 169 9.39 100 54
DL50/ 38
38 44 7 181 9.55 95 54
DL50/ 40
40 45 8 231 11.57 105 66
DL50/ 42
42 48 8 235 11.22 95 66
DL50/ 45
45 52 10 353 15.71 95 99
DL50/ 48
48 55 10 572 23.44 135 132
DL50/ 50
50 57 10 602 24.08 130 132
DL50/ 55
55 62 10 670 24.35 125 132.0
DL50/ 56
56 64 12 790 28.20 115 157.2
DL50/ 60
60 68 12 860 28.60 110 157.2
DL50/ 70
70 79 14 1300 37.10 110 200

DL50 consists of a pair of conical rings and can be used in series (up to 4 sets) to give higher torque ratings.
Note: Customer to supply clamping ring or equipment